Tales of boatbuilding, family, paddling, music, camping, football, snowshoeing, kids, cycling, and whatever else suits my fancy.
Friday, September 29, 2006
Bikes & Commuters
A recent thread in the "Off Topic" section of a paddling forum I often read has gotten me thinking this week about cycle commuting. That thread was full of an awful lot of vitriol, especially from the anti-cyclists (not what I anticipated on a paddling forum). I think one of the cyclist advocates was writing at least a bit tongue-in-cheek, but it certainly wasn't taken that way by some of the other posters. Anyways, a couple of very interesting links to other blogs were posted and I thought I would share them here (since this website actually sees traffic and is much easier to add it to than my main site).
First was a blog posting by Crazy Biker Chick who wrote an article entitled "Things a non-cyclist might not understand Part I: An open letter to motorists who dislike cyclists." I liked this article thoroughly, it is well written, respectful, and in no way does it chide or goad the motorists she hopes to get the point across to. What she says reflects my feelings on the subject quite closely, though there was one point she made that I'm not sure I can agree with (not sure I entirely disagree with it either). She addressed the issue in her most recent post. For more on my feelings on the matter, you can see the rants section of my other web page.
Another blog posting that was linked to was regarding the pro-cycle commuting movement, Critical Mass, and was written by the Accordian Guy in his article Critical Massholes (or: Why I No Longer Ride with Critical Mass). While I appreciate the message they attempt to convey, I've never quite understood how obstructing other vehicles on the road was the best way to get the message across. Let see, piss off a whole bunch of motorists in an effort to get them to afford us more respect? Apparently I wasn't the only person that this has occurred to as evidenced by the aforementioned article.
Now back to kayaks - I gotta go work on the boat (I think I'll glass the outside seams tonight). Ciao.
Thursday, September 21, 2006
Back Adder
Inspired by a photo in Dan Millsip's journal detailing the building of his kayak, I decided to build a device to help me scrape/sand smooth the inside seam in those hard to reach and curved portions of the kayak. Dan credits Daren Neufeld with the pole sanding device.
Here is the problem I'm trying to fix:
In the photo above, the boat is upside down. The tip of the bow curves down and away from the camera (and the guy trying to work in the confined space). The seams are to the sides of the photo. Below are a couple of the closeups of the bumps and glass fibers which stick up (cropped from the right side of the above photo). The whole thing is a big mess of epoxy and fiberglass. 
I stopped by the local Co-Op hardware store on my way home to look for the highly & repeatedly recommended sureform rasp. Not finding one, I picked up some other rasp thing, designed for drywall but the package says it can be used for autobody work. It was cheap so I figured what the hell. I also picked up a couple of small hinges. Here is the first version of my inside seam tool, Inside Seam Tool, MKI:
I fitted the rasp blade to a block of wood which was then attached via a small hinge to a 3 foot length of scrap spruce. This first version did not work very well for 2 reasons - the sole was too flat, and the rasp did not cut the fully cured epoxy very well. I fully expected both of these to be a problem so there were no suprises there. I attempted to curve the rasp but was not very successful and quickly tossed the rasp aside. It was a good thing I sharpened my plane blade last night because I put it to good use by planing down the sole of my block of wood to form a nicely curved surface. While I was at it, I planed down the square corners of the handle to give a handle that I can comfortably grip without fear of gaining a mitt full of splinters (working with a plane and a piece of wood is so much nicer than scraping cured epoxy & fiberglass). I then stapled a piece of 80 grit automotive sandpaper (from a Princess Auto variety pack) to the bottom and voila, Inside Seam Tool, MKII:
Thankfully, the rounded sanding version works much better. It's still gonna be a lot of work and rather slow, reaching with one arm in through the hatch with your head crammed in there too so you can see what you're doing, but my wife has indicated that she'd like to help with the kayak so maybe I can get her to do it.
Wednesday, September 20, 2006
Some Good Ideas from Dan Millsip
* The hinged pole sander for the inside seam (maybe I'll work on that tonight and finally get those jagged edges cleaned up).
* The laminate trimmer slot cutting template - The way I did it by drilling and filing has been less than perfect and now some of those slots are partially filled with epoxy and I have to figure out how to clean them up (maybe I'll grind a file down to the correct thickness).
* Making finger pulls from dowel.
* Making bulkhead templates.
p.s. After about 2 1/2 months away from the kayak I'm getting back at it!
Wednesday, July 12, 2006
Grizzly Industrial - Workshop Planner
Since I am in the process of moving out of our old house/boatbuilding shop and getting a new boatbuilding shop, errr - garage, set-up, this little tool might come in handy to plan the layout of where things go. The common woodworking and shop tools (Grizzly brand of course) are all pre-loaded and available for placement in the layout. Every object can be re-sized so it's easy to change the size to match your own tools. I'll have to play around with this when I have some more time.
Friday, June 30, 2006
Kisseynew & the Yukon River Quest
Go Kisseynew Go!!!
p.s. I just found the gallery of photos from the race here.
Update (July 4th, 2006): The official results have been posted and the awards made. Team 84 Kisseynew - Denesuline Dalutweh finished first in the Voyageur class with a record-breaking time of 42 hours, 56 minutes and 13 seconds, and won the prize of $1500 (which almost covers the $200 per person entry fee).
Congratulations Guys!
N.B. - I originally had the name of the team mixed up, interchanging the words Denesuline Dalutweh (which refers to the name of the first nation to which 3 of the paddlers belong). I had simply copied it from the YRQ website which had it mixed up as well. As it appears above is the corrected name, sorry for any confusion. Thanks to Heather for pointing out the mistake.
While I'm editing this post, I might as well add that one of the members of Team Kisseynew has written an article about his experience in the 2006 YRQ. You can find Ryan Martin's article here, and some photos here .
Thursday, June 29, 2006
Reunification
The inside seams have been fiberglassed using the method described on the Outer Island Kayak web site. The basic process is to cut strips of fiberglass cloth (I made my strips 2 - 2.5" wide, 6 ounce cloth) and use small dabs of hot glue to tack the cloth in place along the shear line of the hull so that the cloth will end up evenly spanning the seam. The deck was then carefully laid over the hull and the ends taped into position. The hull had pulled inwards so the hull and deck did not mate perfectly and I needed to even things up. I found that trying to use tape and straps to bring the hull and deck flush was not that effective, partly because this method can only push the deck inward and does not allow the hull to spread to meet halfway. Also, since the hull overlapped the deck, the pressure from tape and straps pushed the edges past each other rather than causing them to meet. Instead, I used a method I had seen described on the KBBB where u-shaped pieces of wood are tacked to the hull with hot glue near the top edge, then a wedge is driven in past the deck which causes equal pressure pulling the hull outwards and pushing the deck inwards. I found this worked very well and it was easy to convert a bunch of plywood scraps (former strip-holding jigs from when I thought I would build this boat "staple-less") into u's and wedges. I placed a bunch of these jigs along the seam on each side, wherever things needed to be pushed into alignment and used fiber-reinforced strapping tape to tape the halves together. I then attempted to use clear packing tape (too thin, too cheap) to seal the seam but could only manage to do this between the jigs.
With everything aligned and taped up, I turned the boat on it's side and hoisted one end up with a strap from the ceiling such that epoxy poured onto the seam through the hatch opening would run downhill and into the end. I attached a sawed-off brush at a 45 degree angle to the end of a stick and used this to reach in through the hatch openings and push the pool of epoxy where it needed to go to wet out the cloth, ensuring it reached the extremities. With one end epoxied in this way, I raised the other end and did the rest of the seam, then returned the boat to level (still on side). I added a second layer of glass (3" wide, 4 ounce cloth) in the cockpit area for extra strength.
Once this mess had cured for about 24 hours, I knocked the alignment jigs off with a mallet then scraped/cut/sanded away the excess hot glue and all the epoxy that came through. Because my packing tape was crappy, I had trouble getting it off. Because the jigs were in place before I put on the tape, it did little to prevent epoxy from coming through the joint and caused it to pool in many places. As a result, most of my jigs were epoxied in place, though since the epoxy was still only partly cured, they came off without too much trouble.
With the starboard side taped, I then turned the boat over and repeated the process for the other side.
Some comments I have at this juncture:
- Sheer clamps as used on some kayak designs look like a pretty good idea right now. Sheer clamps are strips of wood which extend the length of the boat along the sheer line, providing a surface to which the deck can be attached. Sheer clamps are common on boats which have a fairly flat deck where the deck and hull meet at a sharp angle (not the case in a guillemot).
- Purchased 2" wide fiberglass tape with selvaged edges may produce a neater job than my version of cutting my own strips from regular width cloth on the bias since this would avoid all the loose strands and frayed edges.
- I'm not sure how I'll clean up the rough/sharp surface of the inside seam. I guess I'll have to shape a sanding block of some sort and attach it to a pole. It'll have to be narrow enough to fit most of the way into the tips. I'm not worried about aesthetics here, but the sharp bits of glass fiber that protrude along the seam will shred whatever I put in the hatches.
- The current weight is 35 lbs (no seat, bulkheads, etc) according to the bathroom scale.
See you in August!
Thursday, June 22, 2006
I won, I won!!
Recently, Bear Mountain Boats had a bit of a contest on their boat building forum where they requested forum participants to share their perspective on building small boats, asking the following questions:
- Why have you built your own boat?
- What method did you use and why?
- How do you respond when people say to you 'that's nice but I would never put it in the water'.
- What was your biggest concern before starting to build it? How did you overcome this?
I answered the questions (or at least those applicable at this point) and was thus entered into a drawing for the prize of a boat building class hosted by Bear Mountain in Peterborough, Ontario. I recently received a message from Joan notifying me that the first person offered the prize declined and I was next on the list. Woo Hoo! Now the only problem is to figure out how to get myself to Peterborough for a week (cash in some air miles?). Luckily the prize is a bit open ended so I can wait awhile before claiming my prize, perhaps next winter once I've built up some more time off from my job.
Thank you to Joan & Ted for writing the book that got me interested in boatbuilding in the first place and thanks' for providing the forum where I can learn of techniques from a community of builders.
Tuesday, June 20, 2006
Preparing to Attach Hull & Deck
Regarding my previously posted "To Do List", I can take a couple more items off the list.
Saturday, June 17, 2006
Wednesday, June 14, 2006
Pedro's Woven Rope Carrying Handles
Pedro has very graciously written a set of illustrated instructions and has provided that to the boat-building community. You can find his instructions here.
Friday, June 02, 2006
To Do List, Revisited
a
a
a
4. apply 3rd fill coat to hull & deck?
5. sand the epoxy some more
a
a
8. build & install moby latch system
9. make & install soft padeyes
10. make & install regular padeyes (to be used for internal tie down points)
11. make & install cheek plates
a
13. mate the deck and hull once again and glass the interior seam
14. glass the exterior seam
15. make the seam glass transition "seamless"
16. make & install bulkheads
17. carve seat out of minicell foam
18. build and install backband (I have glassed a curved piece of 1/8" plywood to form the backrest).
19. drill holes at bow & stern for grab loops
20. varnish
21. sand
22. varnish
23. sand
24. varnish
25. install deck lines & bungees
26. install grab loops and toggles
Coaming lip, sanding, hatches cut and hatch lips built
I have gotten a few things done in the last couple of weeks. The first on my "to do" list was to build the cockpit coaming lip, the rim around the top of the cockpit to which the skirt attaches. There are a number of ways to do this. Probably the most common way it is done on strip-built kayaks is as described in Nick Schade's book using 1/4" wide by ~1/8" thick strips of hardwood (ash or walnut are common), wrapped around the top of the coaming with about 6 laminations glued in place. While this is reported to be easy enough, dealing with many thin pieces of wood buttered in epoxy (they get darned slippery) and trying to keep everything aligned didn't have all that much appeal for me. Since the finished product is 1/4" thick by 1/2"-3/4" wide hardwood & glue, it seems to me that this might be heavier than other options. A second common method is that described by Vaclav on the One Ocean website, where a coaming is laid up in carbon fiber (and/or fiberglass, but carbon seems to be common) over top of a form built on the boat out of styrofoam. This method seems simple enough, but I don't have carbon fiber so quite a few layers of glass would likely be necessary to get the required strength and stiffness. Something I began to think about was using thin (1/8") birch plywood reinforced with a couple of layers of fiberglass to form the lip. The birch plywood is thin enough to flex into place and conform to the curvature of the top of the coaming (it is curved from the side profile), but when encased on both sides in layers of glass, should be both stiff and strong. Recently, I saw a post on the KBBB where a builder (Gaetan) used plywood (stained to match the colour of the boat) for his coaming lip. The result looked great and that sealed it - that's how it was going to be done.
The process was fairly simple - I rough cut a piece of 1/8" birch plywood to the size of the cockpit rim, leaving it over-sized to be trimmed later. I oriented the grain perpendicular to the boat so that it flexed into place easily. I then tacked the lip into place on top of the trimmed coaming riser using CA glue (I should have been using accelerator too but the spray pump on the little bottle is buggered and I've given up fighting with it). I then trimmed the inside of the cockpit lip to be flush with the riser and rounded off the corner a bit. I then glassed the lip with 2 layers of bias-cut 4 ounce fiberglass which wrapped from the top of the lip, down the riser, and onto the underside of the deck (barely). The 4 ounce cloth had no trouble making the bends and wets out very easily. It is very nice stuff to work with. Once this had cured, the rough edges at the bottom were smoothed out (a scraper works very well as long as the epoxy is not too hard) and the outer edge of the lip was trimmed down to it's final size of 3/4". I then applied a fillet of epoxy underneath the lip at the junction with the riser to smooth out this corner to a radius the glass can manage, then applied 2 layers of fiberglass which again wrapped from the deck, up the riser and under the the lip. I used a trick I read about on the KBBB to hold this glass in place and make things in this hard to work area "smooth as glass" (described by John Monroe and credited to Rob Macks). I used 3/4" flexible vinyl tubing (purchased at Cdn Tire) squashed in underneath the coaming lip and held in place with spring clamps. Once the glass had partially cured, the tubing was pulled out to reveal ---- a mess! It seems I didn't get the tubing in far enough in many places and there were a lot of voids and air pockets above the glass and underneath the glass. I scraped some of the rough edges I could reach, but there is still a lot of smoothing to go underneath the lip. I may try to put another layer of glass in under the lip since I'm sanding a lot of the strength away in order to clean up the mess. For now, it's not easily seen so it's something I'm working on here and there while focusing on other things. In the end, the plywood coaming lip worked really well and was very easy to do, but I need to work on my technique for glassing underneath. One thing I considered was to put a layer of glass on the underside of the whole lip BEFORE tacking it in place on top of the riser while the glass was still green and flexible. This would have been very easy, but I went for what I thought would be the stronger method by having the glass continuous from deck to riser to lip. Next time, I'd probably do it as I originally considered with putting a layer of glass on the underside of the plywood lip prior to tacking it in place, with a fillet underneath and an extra layer of glass on the outside, avoiding all the trouble of trying to work with glass underneath the installed coaming lip.
While the weather was nice last weekend (overcast but comfortable working temperature) I took the opportunity to drag the boat outside to do some sanding in the fresh air. I also took a few pictures, and sat in the boat to determine the approximate location of the front bulkhead (to ensure I cut my hatch in front of it!).
This week, I cut out the hatches. This went fairly well despite my nervousness about cutting giant holes in the deck of boat. The first step was to determine the shape of the hatches. Using the offset's in Nick's book as a guide, I experimented with a number of shapes. I printed these out on the computer to the right scale which meant taping together a bunch of sheets of paper to create my templates. After considering the diamond shape provided in the book and different egg shapes, I settled on a trapezoid shape with round corners and sides roughly parallel to the sheer line. I then masked off the areas to be cut and with my templates transferred to pieces of cardboard, I traced the shapes onto the boat. Looking at things on the boat, I decided that I had the rear hatch too large, so I scaled it down a bit (about 1/2" all around seemed about right) and moved it aft about 6". This all took me the better part of an evening to get something I was satisfied with.
I started the cut as others have described, using a cutting disc on my dremel. I then used a blade from the jig saw and by hand cut through to make the slot wide enough to fit the jigsaw blade. Then with a new Bosch fine-cut blade and the jig saw on a medium speed, I cut out each hatch. The actual cutting went fairly well. I am glad that I decided not to rush out and purchase a new $200 Bosch jigsaw, and I am glad that I did decide to spend the big bucks and get the Bosh blades (about $12 for a pack of 4). In the end the actual cutting was a bit anticlimactic (which is OK, that means it went well).
With the hatches cut, it was then time to build the hatch lips. I used the method described by Vaclav on the One Ocean web site. Ken (aka Spidey) has some good pictures and a good description of the process on his web site. Before heading to the hardware store I should have double checked what size of weatherstripping to use to form the gasket channel, but I didn't so I just got what looked about right. The 1/8" stuff looked too small, so I went with 1/4" x 3/8" closed cell foam gasket tape. I taped the hatches into position from the outside, adding a couple of strips of cedar to ensure the hatches would sit flush despite any pressure that would be applied in laying up the glass for the lip (not to mention the 20 lbs of wet sand I piled on top). With the deck turned underside-up, I used thin clear packing tape over the whole area to ensure that my gaskets would not yet be a permanent part of the boat. I then applied the self-adhesive weather-stripping to the perimeter of the hatch lid staying about an 1/8" in from the edge. With this in place, I applied a fillet of thickened epoxy (406 filler) pigmented black with graphite powder (mostly because everybody else seems to tint their hatch lips and I didn't want to be left out) on both sides of the weatherstripping. I then began to lay up strips of glass over top of this to make the hatch lip. For the first 1-2 layers, I used 4 ounce glass because it conforms better to curves and does not trap air as easily (I think I still trapped a fair number of bubbles), then followed with strips of 6 ounce glass cloth for a total of 5-6 layers. The glass was wet-out 1 layer at a time using epoxy with graphite powder added to make it black-ish. Once all of the glass cloth was layed up and wet-out, I put a sheet of poly over top and piled damp sand on top of that in an effort to push everything smooth. I was somewhat surprised how long this process took. I started at 10 pm, and did not complete the process until 1:30 am. In the morning, with the epoxy partially cured but still flexible, I removed the sand and the sheet of poly, then peeled the gaskets off of the deck and removed the tape. It all went pretty well, though there are wrinkles from the plastic layed over top. Next, I will trim down the rough edges of the hatch lip, scrape out the weather stripping from the gasket channel, then permanently bond the hatch lip to the underside of the deck.
Friday, May 19, 2006
Gone Paddling

For a good photo of what the river looks like when it is not flush with spring runoff, visit Neil Rawlyk's web site.
Here is a slideshow of photos from the trip:
Sunday, May 14, 2006
Fiberglass, Stage III
My father-in-law was on hand to take lots of photos (in fact, I think the flashes may have prematurely degraded the epoxy) so I'll post some photos later.
While I had the epoxy out, I also made a curved panel that will become the backband. I made a form to the desired backband shape (a more rounded version of the cockpit back shape) out of 1" thick particle board and tacked a piece of 1/8" birch plywood to it, allowing the ply to assume a fair curve. I then used a scrap of 6 oz cloth to glass over top of this and allowed it to cure (where it remains). Once fully cured, I'll remove the glassed plywood from the form, then may glass the inside of the curve (maybe - I'm not sure if the second layer is necessary and may make the backband too stiff). I'll then use this curved piece to cut out the final backband shape, adding slots for the webbing which will hold it in place behind the seat.
With the whole boat now sheathed in fiberglass, I'm practically done right? Here is my current "To Do" list:
- Build cockpit coaming lip
- fiberglass the coaming
- sand epoxy smooth on hull and deck (external)
- apply 3rd fill coat to hull & deck?
- sand the epoxy some more
- cut hatches
- build hatch lips
- build & install moby latch system
- make & install soft padeyes
- make & install regular padeyes (internal tie down points)
- make & install cheek plates
- carve pieces to fit into the extremities to fill the cavities that will be impossible to glass at the seam
- mate the deck and hull once again and glass the interior seam
- glass the exterior seam
- make the seam glass transition "seamless"
- make & install bulkheads
- carve seat out of minicell foam
- build and install backband
- drill holes at bow & stern for grab loops
- varnish
- sand
- varnish
- sand
- varnish
- install deck lines & bungees
- install grab loops and toggles
Once the above list is completed here are a couple more items I could turn my attention towards:
- carve paddles
- make spray skirt
- make paddle float
- build cradles for car-topping
- build cart
- make pump
- make tuuliq
Monday, May 08, 2006
Fiberglass, Stage II
Above: The 1/8 birch ply coaming that caused some grief while glassing, and the region of where the wrinkle was cut out. Below: A close-up of the cut and overlapped region.
One spot I was a bit concerned about was on the fore deck ahead of the cockpit. I inserted into the deck a hand-carved feature (which I'll discuss further in some other posting) which had a fair bit of relief to it. My concern was that the hollows of the carving would trap air and not fill properly with epoxy (although the carving had been previously coated and the hollows were partially filled). We took care of this area by lifting the cloth and filling the hollows of the carving with unthickened epoxy, then laying the cloth back down, and continuing to brush on the epoxy on the deck as we had been doing. It seemed to tun out fairly well with only a couple of smallish bubbles trapped under the glass (I may try to get these out with a syringe & needle). I must be getting better at squeegeeing because this went much better this time than on the hull. All in all I'm extremely happy with how the deck has turned out so far.
Above: The glassed deck in the foreground, the hull in the background.Now the inside of the hull on the other hand .... Well let's just say it's a good thing it'll be under the deck and if someone examining the boat has the audacity to stick their head into the hatch to have a look, I'll just hit them over the back of the head with a greenland paddle. I didn't fill the gaps inside the hull and I didn't sand to the same level of perfection as on the outside. I chose to get aggressive with those epoxy drips and that meant attaching a 36 grit sanding disc to the drill and going after them. For the record, 36 grit will chew through cedar and anything else in it's way VERY quickly. Although I never went all the way through, there is the occasional divot (read gouge). I sanded the hull to 80 grit with the ROS to take most of the gouges from the 36 grit disc out, particularly in the cockpit area. Working in the concave and confined regions of the bow and stern was a bit tricky and I didn't spend a lot of time there to fair things out. I used a fillet in these regions so that the v of the bottom and the stems were rounded out to allow the glass to lay into the hollow a bit better. Getting the glass to stay tight in at the bottom of the stems was still a bit difficult, with the glass wanting to pull up and away. One thing I thought of but didn't try was to use bags of sand in these areas to weigh down the glass, pushing it tight into the cavities. This method would have the added benefit of squeezing out the excess epoxy. I also found squeegeeing inside the hull to be difficult. It seemed that no matter how careful I was, the squeegee would pull the cloth away from the relatively sharp corners at the chines (imagine the troubles I might have with a hard-chined boat!). As a result of this combined with the difficulty of squeegeeing in the confined space at the bow and stern, I am sure I have more epoxy in the hull than I should. Incidentally, I added a second layer of 6 oz. glass in the bottom of the cockpit area (layed out underneath the larger glass cloth sheet covering the rest of the hull).

In addition to the troubles already mentioned, in the hull I also had bubbles forming from air coming out of the wood itself. I had heated the shop to 20C overnight and things were a nice steady temperature by the morning and the heat was turned off (everybody knows you want the temperature to be steady or dropping while doing the fiberglassing). We started our epoxy work in the morning on the deck and after lunch moved to the hull. As we worked on the hull, we noticed it starting to get rather warmish in the shop. The weather outside had risen to a beautiful 20C in bright sunshine, so that may have been helping to warm the shop, but I didn't think that it would make that much difference in a well-insulated shop with a concrete floor that is still holding the cool of a Canadian winter in it's mass. I am therefore led to wonder if the rising temperature was due, in part at least, to the exothermic reaction of curing epoxy. Through the afternoon the temperature inside the shop rose to 24-25C. The temperature rise produced the promised result - bubbles formed under the glass as expanding gasses escaped the wood but then with the wood sealed on the outside, were trapped in thickening epoxy on the inside. Many of these bubbles did actually find their way to the surface, but at least a few did not despite my encouragement. I'm not overly concerned about their presence, but I'm glad it happened on the inside of the hull and not on the topside of the deck.
In the end, I'm not too concnerned about the imperfections inside the hull. My wife suggested the extra bubbles should be considered flotation and I think that's a good approach at this point. The glassing of the underside of the deck should go a bit more smoothly - the curvature is much less than the hull and there are no tight confines to work within and no chines to deal with. Also, the gaps between strips are much less than occured on the hull (again due at least in part to less curvature) so the surface is smoother. My peak this morning under the deck also indicated that there are far fewer epoxy drips coming through to deal with. I think I'll put the 36 grit sanding disc away and stick to hand sanding or a random orbital sander with at least 80 grit paper. For glassing underneath the deck I'll be using 4 ounce West Systems cloth, doubled (tripled?)around the cockpit to provide some extra strength for sitting on the deck while getting in and out.
Below: One final photo for the night - taken on Saturday when my daughter was helping me sand/scrape/grind the inside of the hull in preparation for fiberglass.